INFO STOC Solicita stoc sau informatii produs!
Livrarea se face in limita stocului disponibil
Asigurati-va de disponibilitatea produsului ce urmeaza sa il comandati, puteti face acest lucru telefonic sau pe email
Preamplificator Phono Teac PE-505
Echipa AVmall incearca sa mentina acuratetea informatiilor din acesta prezentare. Cu toate acestea, in anumite cazuri, pot aparea mici inadvertente pentru a caror semnalare va suntem recunoscatori. Ne poti contacta oricand pentru a clarifica eventuale nelamuriri. Nu uita sa mentionezi in corespondenta ta numele exact al produsul. Fotografia produsului Preamplificator Phono Teac PE-505 are caracter informativ si poate sa difere de produsul real sau sa contina accesorii neincluse in pachetul standard al produsului. Specificatiile tehnice pot contine erori de operare si pot fi schimbate fara instiintare prealabila de catre producator, neconstituind obligativitate contractuala.
7.999,00 RON / Bucata
Disponibilitate: In stoc furnizor
* Verificati disponibilitatea inainte de a comanda!
* Verificati disponibilitatea inainte de a comanda!
Ai gasit mai ieftin? Suna pentru cea mai buna oferta!
Oferta personalizata si reducere pentru 2 sau mai multe produse. Suna acum si afla!
Cantitate:
−
+
De la: 1333.17 lei / luna
Livrarea este gratuita in Bucuresti si provincie (daca comanda depaseste 500 ron), timpul de livrare este de 24-48 de ore, in cazul in care s-a facut confirmarea livrarii de catre AVmall.
The PE-505 is a phono equalizing amplifier with dual monaural and fully-balanced input/output circuits that support balanced MC input.
The development of the PE-505 was achieved by relying on TEAC′s audio technology expertise, focusing on recording and playback, with the goal of accurately reproducing the original intent of the recording producers. The PE-505 will amplify even very faint audio signals picked up by the cartridge, process them without coloration, and then deliver them faithfully in order to keep the listener as close as possible to the original sound that was played before it was engraved on the master disc.
The high precision RIAA correction circuit, as well as both DECCA and COLUMBIA curves are supported. In addition, selectable load resistance for MC cartridges and load capacity for MM cartridges are present; allowing users to optimize the settings for the type of cartridge used and for the condition of the record.
Fully-balanced circuit design
From the head amplifier to the equalizing amplifier sections to the buffer amplifier section on the final output stage; the PE-505 employs a fully-balanced circuit design throughout all stages that amplifies, equalizes, and maintains signal purity of even the most extremely faint audio signals picked up by a cartridge.
Even unbalanced signal on the conventional RCA input is converted to the differential processing mode right after the input terminals.
Equalizing circuit on the differential cartridge outp
Absorbing errors on the balanced output, the differential output equalizing circuit delivers a more accurate audio signal. The differential output circuit that cross-multiplied the hot and cold outputs each other. As the result, both signals are equalized for a pure and natural audio signal delivery.
High-precision RIAA circuit
A newly developed NF-type equalizing amplifier achieves less than ±0.05dB of RIAA deviation.
(20Hz to 20kHz)
High Signal-to-Noise ratio
The PE-505 achieves 106dB on the RCA input*1, and 86dB on the XLR input*2, while the residual noise voltage reaches 10μV on the MM and 85μV on the MC*3 which are sophisticated.
*1 MM *2 MC *3 XLR input
High-precision OLD EQ curves
As well as the modern RIAA curve, individual curves on monaural records from DECCA and COLUMBIA issued before the RIAA curve was defined in 1955 are also supported.
Versatile settings and unique measuring functions
The PE-505 equips switchable load-capacity for MM cartridges and switchable load-resistance for MC cartridges. Furthermore, the load-resistance measuring function allows users to select an appropriate load-resistance by pressing the MEASURE key on the front panel to show the total load-resistance value including cable resistance on the gauge.
Also, the Subsonic function shows subsonic signals less than 6Hz on the gauge, while the subsonic filter (17Hz, -24dB/octave) cuts unnecessary low frequency out of the hearing range.
DEMAG function to refresh the cartridges
With the quick demagnetize function, both magnetized iron cores of MC cartridges and the step-up transformer are demagnetized by playing back a vinyl record for as short as 30 seconds with the DEMAG position.
Features at a glance
- Full differential inputs/outputs circuits
- High-precision RIAA EQ circuit achieves less than 0.05dB of deviation
- Individual EQ curves for monaural records and ones with EQ from DECCA and COLUMBIA
- Balanced MC input
- Switchable MC impedance (10, 22, 47, 100, 220, 470, 1kΩ)
- Switchable MM load-impedance capacity (0, 100, 220, 330pF)
- MC load-impedance measurement function
- Switchable MM/MC gain (High/Low)
- Subsonic detection
- Subsonic filter (17Hz, −24dB/oct.)
- MONO function that mixes left and right channels as a monaural channel
- DEMAG function that de-magnetizes cartridge
- 3-position pin-point feet
- GND terminal
- RoHS compliant
Important: Conținutul acestei descrieri de produs a fost tradus automat și poate conține erori atât de vocabular, cât și de sintaxă și gramatică.
Specificatii Preamplificator Phono Teac PE-505
| Specificatii | Amplifier section Total harmonic distortion (Rated output, 1kHz, GAIN Low) RCA input (MM) 0.002% RCA input (MC) 0.02% XLR input (MC) 0.02% Residual noise volt (Input short, GAIN low, IHF-A) RCA input (MM) 10μV RCA input (MC) 65μV XLR input (MC) 85μV S/N ratio (Input short, Rated input, GAIN Low, IHF-A) RCA input (MM) 106dB XLR input (MC) 86dB RIAA deviation (20Hz to 20kHz) ±0.05dB Channel separation −90dB or higher (MM, 10kHz, GAIN Low) Gain GAIN LOW RCA input (MM) 34dB RCA input (MC) 54dB XLR input (MC) 54dB GAIN HIGH RCA input (MM) 46dB RCA input (MC) 66dB XLR input (MC) 66dB Subsonic filter 17Hz, −24dB/octave Phono input section Unbalanced input RCA Pin (MC/MM compatible) × 1 pair Max input level 150mV (MM, THD 0.1%, GAIN Low) 16mV (MC, THD 0.1%, GAIN Low) Input impedance* MM 47kΩ, Load-impedance: 0, 100, 220, 330pF MC 10, 22, 47, 100, 220, 470, 1kΩ Balanced input XLR (MC only) × 1 pair Max input level 16mV (MC, THD 0.1%, GAIN Low) Input impedance* MC 10, 22, 47, 100, 220, 470, 1kΩ * switchable from the Settings Analog output section Unbalanced output RCA pin × 1 pair Rated output level 2Vrms Output impedance 63Ω Balanced output XLR × 1 pair Rated output level 4Vrms Output impedance 126Ω Power supply AC120V, 60Hz AC220 - 240V, 50/60Hz Power consumption 14W Overall dimensions(W × H × D) 290 × 84.5 × 252.5 mm / 11.4 × 3.3 × 9.9 Weight 4.5kg / 10.0 lbs. Included accessories Power cord × 1, Cushions for foot × 3, Owner′s manual × 1 * RoHS complied. * Spec and design are subject to change without notice. |
Pentru Boxe:
- Pentru performante optime este necesara pozitionarea boxelor la o distanta de minim 30-40cm de peretele din spate pentru boxele cu bass-reflex in spate, pentru cele cu bass-reflex in fata, recomandam pozitionarea la o distanta de 10-20cm fata de peretele din spate.
- Boxele vor ajunge sa functioneze in parametrii recomandati de producator, dupa minim 50 de ore (ideal 100 ore) de functionare la volum mediu. In aceasta perioada de timp, de “rodaj a boxelor”, sunetul va fi la inceput ceva mai artificial, bass-ul nu va fi inca controlat, inaltele rigide iar vocile usor retinute, pe masura ce boxele vor functiona, veti remarca cum bas-ul devine mai controlat, mai prezent si mai voluminos, vocile si sunetele medii devin naturale si mai echilibrate, iar inaltele devin rafinate si detaliate. Exista boxe care necesita un „rodaj” mai amplu de minim 300 de ore mai ales in cazul celor care au difuzoare de kevlar, carbon sau alte materiale de acest tip. Boxele care se „rodeaza” cel mai repede sunt cele care au difuzoare de celuloza.
Pentru Amplificatoare, DAC-uri, Preamplificatoare, Receiver Stereo & Home Cinema, Surse digitale audio-video:
- Pentru performante optime este necesar „rodarea” echipamentului, In functie de complexitatea componentelor din aparatul dumneavoastra acesta poate dura intre 30-200 ore.
- Rodajul se face la volum minim, fiind astfel suficient faptul ca acesta este alimentat corect conform manualului de utilizare la 220-230 Volti si trece semnal audio sau video dupa caz prin el.
- Echipamentul supus „rodajului” va ajunge sa functioneze in parametrii recomandati de producator, dupa perioada mai sus mentionata. In aceasta perioada de timp, de “rodaj”, sunetul va fi la inceput ceva mai artificial, bass-ul nu va fi inca controlat, inaltele rigide iar vocile usor retinute, pe masura ce echipamentul va functiona, veti remarca cum bas-ul devine mai controlat, mai prezent si mai voluminos, vocile si sunetele medii devin naturale si mai echilibrate, iar inaltele devin rafinate si detaliate.
Pentru cabluri:
- Pentru performante optime este necesara „rodarea” cablurilor, In functie de complexitatea conductorului folosit, cat si geometriei acestuia, „rodajul” poate dura intre 30-100 ore.
- Rodajul se face la volum minim, fiind astfel suficient faptul ca va trece semnal audio sau video dupa caz prin el.
- Cablul supus „rodajului” va ajunge sa functioneze in parametrii recomandati de producator, dupa perioada mai sus mentionata. In aceasta perioada de timp, de “rodaj”, sunetul va fi la inceput ceva mai artificial, pe masura ce cablul va functiona, veti remarca cum bas-ul devine mai controlat, mai prezent si mai voluminos, vocile si sunetele medii devin naturale si mai echilibrate, iar inaltele devin rafinate si detaliate.
Pentru detalii privind aceste aspecte de rodaj si nu numai, va rugam sa ne consultati!
