Amplificator Integrat Bryston B1353

  • Amplificator Integrat Bryston B1353
  • Amplificator Integrat Bryston B1353
Echipa AVmall incearca sa mentina acuratetea informatiilor din acesta prezentare. Cu toate acestea, in anumite cazuri, pot aparea mici inadvertente pentru a caror semnalare va suntem recunoscatori. Ne poti contacta oricand pentru a clarifica eventuale nelamuriri. Nu uita sa mentionezi in corespondenta ta numele exact al produsul. Fotografia produsului Amplificator Integrat Bryston B1353 are caracter informativ si poate sa difere de produsul real sau sa contina accesorii neincluse in pachetul standard al produsului. Specificatiile tehnice pot contine erori de operare si pot fi schimbate fara instiintare prealabila de catre producator, neconstituind obligativitate contractuala.
Solicita pret!
STOC: In stoc furnizor

Ai gasit mai ieftin? Suna pentru cea mai buna oferta!

Oferta personalizata si reducere pentru 2 sau mai multe produse. Suna acum si afla!

Livrarea este gratuita in Bucuresti si provincie (daca comanda depaseste 299 ron), timpul de livrare este de 24-48 de ore, in cazul in care s-a facut confirmarea livrarii de catre AVmall.

Bryston B1353

amplificator stereo integrat

Bryston B135 SST2 Integrated Amplifier este fara indoiala cel mai transparent din punct de vedere sonor, si cel mai fiabil produs audio disponibil. Ofera nivele de performanta ce egaleaza cele mai rafinate componente audio separate.

Intrari: 6x RCA Single Ended Pairs, 2x RCA Single Ended Pairs (Record In, Power Amp In), 2x Optical (TOSLINK)*, 2x SPDIF (RCA)*
Iesiri: 2x RCA Single Ended Pairs (Record Out, Preamp Out), Speaker Terminals, 1/4 inch Headphone Jack
Control: RS-232 (DB9), AUX IR, 2x 12V Output Triggers.

Specificatii Amplificator Integrat Bryston B1353

Specificatii Telecomanda optionala BR2
Front plate negru sau argintiu
B-135P Amplificator integrat cu Phono MM
*B-135DA Amplificator integrat cu 4 intrari digitale
*B-135P/DA Amplificator integrat cu Phono MM si 4 intrari digitale
POWER AMPLIFIER SECTION:
POWER OUTPUT: Nominal: 135 watts/channel into 8 Ohm
Maximum: 165 Watts/channel at onset of clipping into 8 Ohm @ 1 KHz
1/8th max: 20.6 Watts per channel into 8 Ohm @ 1KHz
INPUT IMPEDANCE: 50K ohms single ended
SENSITIVITY: 1v = 100 Watts into 8 ohms (gain = 28.28 or 29dB)
DISTORTION: THD+noise: ‹ 0.005% 20Hz to 20kHz at 135 Watts into 8 ohms,
IMD: ‹ 0.005 60Hz + 7KHz mixed 4:1
NOISE: ›108dB below rated output (with 20Hz to 22KHz bandpass filter)
SLEW RATE: › 60 volts per microsecond
POWER BANDWIDTH: ‹1 Hz to over 100 kHz
DAMPING FACTOR: Over 500 at 20 Hz, ref. 8 ohms
PREAMPLIFIER SECTION:
FREQUENCY RESPONSE: 20Hz to 20KHz, ±.05dB
IMD OR THD: ‹.003%
HIGH LEVEL SENSITIVITY: 500mV
NOISE: 100dB @ 20Hz to 20KHz (ref: 1V input)
GENERAL:
POWER CONSUMPTION: Maximum: 609 Watts (both channels at onset of clipping)
Standby:
@ 100VAC line voltage ˜ .85Watts
@ 120VAC line voltage ˜ .98Watts
@ 220VAC line voltage ˜ 1.8Watts
@ 240VAC line voltage ˜ 2.0Watts
SHUT DOWN VOLTAGE: When line voltage drops below these levels the amplifier will automatically shut down.
100VAC models ˜ 78 VACshutdown
120VAC models ˜ 81 VACshutdown
220VAC models ˜ 190 VACshutdown
240VAC models ˜ 195 VACshutdown
HEAT LOAD:
At maximum output power, both channels driven at 160WOUT ˜ 986btu/hr
At 1/8th output power, both channels driven at 20WOUT ˜ 594btu/hr
Standby mode:
for 120VAC models ˜ 3.35 btu/hr
for 220VAC models ˜ 6.83 btu/hr
DIMENSIONS: 17” or 19” wide X 4.55” high X 14” deep
(433 or 483mm X 116mm X 353mm)
WEIGHT: 13.6kg
Tip Echipament Solid State

Nu sunt recenzii pentru Amplificator Integrat Bryston B1353. Fii primul care scrie una!


Spune-ti parerea

Trebuie sa fii autentificat pentru a comenta!

Produse similare