Accesoriu pentru Analog Player fo.Q DS-25E

  • Accesoriu pentru Analog Player fo.Q DS-25E
Echipa AVmall incearca sa mentina acuratetea informatiilor din acesta prezentare. Cu toate acestea, in anumite cazuri, pot aparea mici inadvertente pentru a caror semnalare va suntem recunoscatori. Ne poti contacta oricand pentru a clarifica eventuale nelamuriri. Nu uita sa mentionezi in corespondenta ta numele exact al produsul. Fotografia produsului Accesoriu pentru Analog Player fo.Q DS-25E are caracter informativ si poate sa difere de produsul real sau sa contina accesorii neincluse in pachetul standard al produsului. Specificatiile tehnice pot contine erori de operare si pot fi schimbate fara instiintare prealabila de catre producator, neconstituind obligativitate contractuala.
128,25 RON
Disponibilitate: Acest produs nu se mai fabrica, nu mai este disponibil in stoc.

Ai gasit mai ieftin? Suna pentru cea mai buna oferta!

Oferta personalizata si reducere pentru 2 sau mai multe produse. Suna acum si afla!

Livrarea este gratuita in Bucuresti si provincie (daca comanda depaseste 299 ron), timpul de livrare este de 24-48 de ore, in cazul in care s-a facut confirmarea livrarii de catre AVmall.

This product is an audio quality-improving seal for optical discs, utilizing an organic polymer hybrid damping material with the highest level of vibration-absorption performance. Simply apply the 0.3-mm thick ring-shaped seal to the center of a CD, DVD, or other optical disc to absorb the minute levels of unnecessary vibration generated during playback with amazing efficiency, and greatly attenuate the physical and electrical noise caused by this vibration. This makes the sonority, spread, thickness, and subtlety of the sound extremely true to life, dramatically improving the ability to reproduce the original sound. Additionally, the center (remaining) portion of the ring-shaped seal can be used to remove remaining adhesive, or to tune the device.

The number of DS-25 rings has been increased from 11 to 18, thus reducing the unit cost.
Not only that, but further advancements have enhanced the sound quality and enabled a higher level of fidelity.


USAGE

Be careful not to cut yourself with the plastic spatula when removing it from the case or using it to peel off or apply the seal.


? When removing the seal from a disc, be sure to completely remove any remaining adhesive. If adhesive from the seal remains on the disc, then the audio device could become damaged the next time the disc is played.


? When removing adhesive from a disc, you can use the remaining center portion from the seal ring. Press the adhesive portion of the seal to the disc several times; this will cleanly remove the adhesive.


Peel off the seal by using the plastic spatula.


Put the seal on the center of the case with the adhesive face of the seal upturned.


Put the disc on the case with the label said downward ,and firmly press the seal.

Product specifications
Package contents 18 ring-shaped vibration-damping seals (thickness: 0.3 mm)
Plastic spatula: 1


About High Damping Material fo.Q


‘fo.Q′ is a product applying materials developed with the support of JST (Japan Science and Technology Agency).
Vibrational energy is converted to electric energy, and finally to heat energy, enabling efficient absorption.
There are no rubber or heavy metal overtones, and efficient attenuation of the finest vibrations,
considered difficult to remove up to now, promise you the purest and clearest tones.

Damping performance of ‘fo.Q′


The graph to the left shows the difference in damping when ‘fo.Q′ is adhered to metal products, and the same level of vibration is applied. Using ‘fo.Q′ makes it possible to dampen the vibration of materials much more quickly than when it is not used. This benefit quickly and efficiently dampens the vibration of audio equipment, improving the audio quality and raising the signal-to-noise ratio.

Comparison of damping performance with ‘fo.Q′ and conventional damping materials


The damping material used in ‘fo.Q′ has at least twice the damping performance of conventional damping materials.Additionally, with conventional damping material, damping performance falls as strain decreases, ultimately reaching zero. In contrast, the damping material used in ‘fo.Q′ features the property that as strain decreases, damping performance increases. These properties enable ‘fo.Q′ to quickly and efficiency damp the minute vibrations generated by audio equipment, making it possible to enjoy clear, flowing audio.

Loss factor is a measure of damping performance. The higher the loss factor, the better the damping performance is.
Here the term “strain” refers to the vibration itself; it does not refer to strain in the audio.

Damping performance comparison with the conventional inorganic boards and ‘fo.Q′ audio boards


‘fo.Q′ audio boards have an average of 10 times the damping performance of conventional inorganic boards over the entire frequency band. In the low-frequency band (300 Hz and below) and the high-frequency band (4,000 Hz and above) in particular, the damping performance is extremely high.These effects enable ‘fo.Q′ to dramatically dampen low and high-frequency noise in particular, clarifying the contours of once difficult-to-hear audio. It also eliminates distortion when audio is played at high volumes.

Specificatii Accesoriu pentru Analog Player fo.Q DS-25E

Specificatii fo.Q este un renumit producator japonez, brand de prestigiu considerat de toti specilistii domeniului ca fiind lideri de piata in domeniu tweaks/gadget si audio accesories

About High Damping Material fo.Q

‘fo.Q′ is a product applying materials developed with the support of JST (Japan Science and Technology Agency).
Vibrational energy is converted to electric energy, and finally to heat energy, enabling efficient absorption.
There are no rubber or heavy metal overtones, and efficient attenuation of the finest vibrations,
considered difficult to remove up to now, promise you the purest and clearest tones.
Pentru Boxe:

- Pentru performante optime este necesara pozitionarea boxelor la o distanta de minim 30-40cm de peretele din spate pentru boxele cu bass-reflex in spate, pentru cele cu bass-reflex in fata, recomandam pozitionarea la o distanta de 10-20cm fata de peretele din spate.

- Boxele vor ajunge sa functioneze in parametrii recomandati de producator, dupa minim 50 de ore (ideal 100 ore) de functionare la volum mediu. In aceasta perioada de timp, de “rodaj a boxelor”, sunetul va fi la inceput ceva mai artificial, bass-ul nu va fi inca controlat, inaltele rigide iar vocile usor retinute, pe masura ce boxele vor functiona, veti remarca cum bas-ul devine mai controlat, mai prezent si mai voluminos, vocile si sunetele medii devin naturale si mai echilibrate, iar inaltele devin rafinate si detaliate. Exista boxe care necesita un „rodaj” mai amplu de minim 300 de ore mai ales in cazul celor care au difuzoare de kevlar, carbon sau alte materiale de acest tip. Boxele care se „rodeaza” cel mai repede sunt cele care au difuzoare de celuloza.

Pentru Amplificatoare, DAC-uri, Preamplificatoare, Receiver Stereo & Home Cinema, Surse digitale audio-video:

- Pentru performante optime este necesar „rodarea” echipamentului, In functie de complexitatea componentelor din aparatul dumneavoastra acesta poate dura intre 30-200 ore.

- Rodajul se face la volum minim, fiind astfel suficient faptul ca acesta este alimentat corect conform manualului de utilizare la 220-230 Volti si trece semnal audio sau video dupa caz prin el.

- Echipamentul supus „rodajului” va ajunge sa functioneze in parametrii recomandati de producator, dupa perioada mai sus mentionata. In aceasta perioada de timp, de “rodaj”, sunetul va fi la inceput ceva mai artificial, bass-ul nu va fi inca controlat, inaltele rigide iar vocile usor retinute, pe masura ce echipamentul va functiona, veti remarca cum bas-ul devine mai controlat, mai prezent si mai voluminos, vocile si sunetele medii devin naturale si mai echilibrate, iar inaltele devin rafinate si detaliate.

Pentru cabluri:

- Pentru performante optime este necesara „rodarea” cablurilor, In functie de complexitatea conductorului folosit, cat si geometriei acestuia, „rodajul” poate dura intre 30-100 ore.

- Rodajul se face la volum minim, fiind astfel suficient faptul ca va trece semnal audio sau video dupa caz prin el.

- Cablul supus „rodajului” va ajunge sa functioneze in parametrii recomandati de producator, dupa perioada mai sus mentionata. In aceasta perioada de timp, de “rodaj”, sunetul va fi la inceput ceva mai artificial, pe masura ce cablul va functiona, veti remarca cum bas-ul devine mai controlat, mai prezent si mai voluminos, vocile si sunetele medii devin naturale si mai echilibrate, iar inaltele devin rafinate si detaliate.

Pentru detalii privind aceste aspecte de rodaj si nu numai, va rugam sa ne consultati!

Nu sunt recenzii pentru Accesoriu pentru Analog Player fo.Q DS-25E. Fii primul care scrie una!


Spune-ti parerea

Trebuie sa fii autentificat pentru a comenta!

Produse similare